Frick evaporative condenser

This super-efficient evaporative condenser minimizes energy consumption by providing lower condensing temperatures through high efficiency, low horsepower axial fans. The objective of a mechanical refrigeration system is to remove heat from a space or product, and to reject that heat to the environment in some acceptable manner. Evaporative condenser s are used to reject heat from mechanical refrigeration systems. The evaporative condenser is a combination.

Home IMECO-Parts FRICK -Parts. Authentic factory replacement parts for your IMECO units.

The steel panels and structural elements are constructed of heavy-gauge G-2hot-dip galvanized steel. EVAPORATIVE COOLING PRODUCTS. The IDSC condenser offers all 304L stainless steel construction and 316L. F condensing temperature, 20ºF suction temperature and 78ºF wet bulb temperature. The IDCinduced draft, axial fan, evaporative condenser is designed to reduce installation time by incorporating new alignment features and a robust construction.

Steel coil construction, drift eliminators included (may need to be replaced). Condenser Specifications XLC 85. The addition of fill surface to the traditional evaporative condenser design reduces evaporation in the coil section, reducing the potential for scaling and fouling.

The unit is designed to combat problems from changes in water treatment chemistry that can lead to white rust, corrosion and decreased product life in conventional galvanized steel condensers.

For Zero suction pressure or straight refrigeration to -10°F Liquid. Ammonia or newer refrigerants can be used also. Non Corroding PVC moisture eliminators. Unit was part of a refrigeration system for a dough plant. Tons ammonia nominal rating. Eclipse refrigerating machines. Describes evaporator and evaporative condenser design, selection, and operation. NOTE: of the cells have sold. A small portion of the water is evaporate removing heat from the refrigerant, and condensing it inside the coil.

Therefore, like the cooling tower, all of the heat rejection is by evaporation, thus saving about of the water normally required by a “once-through” system. Their installation and specifically the installation of the piping to and from the evaporative condenser has a direct effect on their operation and the overall energy efficiency of the refrigeration system. Nominal capacity: tons using R-7(ammonia) at 96.

Pumps Motors Package Units. Energy‑saving features reduce operating costssignificantly. Your plant’s performance depends uponrefrigeration equipment reliability and efficiency. To obtain more information about what parts we sell or to get a quote on a part, please fill out a request form. Total Cost of OwnershipWhile.

This section will describe some of the various con-fi gurations that may be used with regard to electrical control. To find a Imeco york evaporative condenser manual, you only need to visit our website, which hosts a.

In the high pressure parts of a refrigerator, a condenser is used to remove the heat of the hot vapour refrigerant discharged from the compressor. Frick Industrial Refrigeration. Evaporators coils are used in low pressure refrigerators and cool down air by absorbing heat. We supply a wide range of manufacturers, models and specifications to the global marketplace.

You are welcome to contact us to discuss your specific requirements. The vapour to be condensed is circulated through a condensing coil, which is continually wetted on the outside by a re-circulating water system. State-of-the-art screw compressor packages and pac-chillers feature VSD. Hygienic air handlers, air units, evaporators, evaporative condensers, remote evaporator packages, heat exchangers, vessels and controls.

Further, the heat transfer coef cient for the evaporative system is higher than for air-cooled condensers. This enhances the heat transfer rate and increases the value of the overall heat transfer coef cient. As a result, a smaller heat transfer area is used to remove the same thermal load in air-cooled condensers. EVAPCO offers a variety of evaporative condenser designs in Each unit is a reflection of Evapco’s commitment to excellence in engineering and manufacturing.

An emphasis on research and development has resulted in many condenser innovations. This process disposes of condensation in a way that improves the device efficiency. This system has made its place permanently in refrigeration-industry because a broad range of 41-5ammonia tons could be covered with it. Imeco evaporative condensers and Frigid Coil cooling coils. FRICK Industrial Refrigeration This website requires certain cookies to work and uses other cookies to help you have the best experience.

Commercial Product Price List Commercial Products Prices listed by Product Family including options (where appropriate). It is suitable for replacing opportunities along with expanding new-projects. An evaporative condenser of the push-through type has the blower located directly beneath the coils and its horizontal discharge directed upwardly at an angle from the horizontal. As a water-cooled condensers, evaporative cooling of condensers first transfer of heat into the water, and then from the water outdoors.

If you need a new compressor, pump or evaporative condenser to replace the old one we can provide you one from the manufacturer you need. We work with OEMs and manufacturers throughout the petro-chemical and refrigeration industry so if there is something you nee we can get it. SPX Cooling Technologies, Inc.

For more than a century, we have provided exceptional quality equipment and service to the process cooling, industrial, refrigeration, and HVAC markets. The package chills ethylene glycol to 10°F, which is used to build ice in two 10ton-hour Ice storage modules.